PREPARATION - Adjusting the collar to the spray device

1. Remove the keeper from the black collar (1). Pass the black collar through the loops (2) of the spray device (3) while making sure that the collar does not block the microphone’s opening (4). Put the keeper back on the collar (5). The curved edge of the keeper should face inside.

2. Feed the free end of the collar into the slot of the buckle that is closest to the Multivet logo from the back to the front (6). Then, thread the free end of the collar through the outside slot from the front to the back (7). The free end should now hang on the outside, then thread the keeper (8). When you have completed this section, the assembled collar looks as illustrated (9).

Take off all other collars your dog may be wearing and place the Spray Collar around his neck, making sure the spray valve is directed toward the snout. Adjust the collar to fit like a regular collar. You should be able to easily pass two fingers (10) between your dog’s neck and the device. We suggest that you check the collar regularly to make sure that it is well adjusted.

Note: If these instructions are not properly followed, the buckle can easily be pulled off the collar. This could lead to the device being lost or damaged. A collar lost or damaged through the collar strap being incorrectly threaded is not covered under warranty.

Your dog must get used to the device before you actually start using it. We suggest that you make your dog wear the Anti-Bark Spray Collar during 4-5 days before inserting the battery and filling the device. At the same time, we also suggest that you remove and put the collar back frequently on your dog. To familiarise your dog with the anti-bark device.

FILLING THE DEVICE

1. Place the device on a flat surface, with the fill-up valve turned upwards (11).
Shake the refill before using it.

2. Hold the can upside down, then insert the aerosol tip in the fill-up valve - the deepest cavity (12) - then press down firmly for 10 to 20 seconds, then release.

Note: If spray is escaping as you attempt to fill the device, increase the downward pressure on the refill can to get a better seal. You cannot overfill the device. When completely filled, there should be enough gas in your device for 25 strong sprays.

INSERTING THE BATTERY

Slide off the battery cover (14) and insert the 6-volt alkaline battery without forcing it (15), keeping the polarity in mind (+ and -). Slide the cover back on (16).

Turn the device on - Before every use, it is best to test the device by simulating a dog’s bark into the microphone.

Adjust the Spray Collar onto the dog’s neck with the microphone’s opening facing inwards. Direct the spray valve towards the dog’s snout.

Your Anti-Bark Spray Collar will now react when your dog barks. Training, in addition to using the device will accelerate and consolidate the desired behaviour modification.

For Best Results we recommend that:
The collar should be worn only during periods of nuisance barking and no more than 8 hours per day.

Your dog must get used to the device before you actually start using it. We suggest that you make your dog wear the Anti-bark Spray Collar for 4-5 days before inserting the battery and filling the device. At the same time, we also suggest that you remove and put the collar back frequently on your dog.
It is important that your dog's hair doesn't block the spray valve. Try tying a bandanna (hankerchief) around your dog's neck, and then place the spray collar over it. If necessary, you may also consider trimming a little of the long hair around the dog's neck for better spray effect.

Remove all other collars with metallic parts or tags. These could create noise that may needlessly activate the spraying device.

Avoid letting your dog wear the device with an empty reservoir. Make sure it is always full.

Never fasten a leash to the Anti-bark Spray Collar.

If you dog tries to take off the device, a harness can be used instead of the collar provided. Dog harnesses can be found in all good pet shops.

The collar should be loose enough to pass two fingers between your dog's neck and the device. Check the collar regularly to make sure that it is well adjusted.

Keep the device clean at all times. Do not immerse it in water when cleaning. Simply use a dry cloth to wipe away dirt. You may lightly brush with and old toothbrush if dirt has accumulated in from to the microphone grid.

The device should be switched off when you are filling the unit or not using it.
Make sure the collar strap doesn't cover the microphone hole. Please refer to the filling instructions printed on the back of the ABS packaging.

Before every fourth fill release propellant/air from the device by depressing the centre pin of the refill valve with the end of a biro. If liquid is released stop!, this means that the unit is full of citronella. If the unit expels mainly air (no citronella liquid) keep depressing unit until all air is gone.

Follow refilling procedures as per filling instructions.

Always make sure the device is full of citronella when being put on the dog.

Please make sure the device doesn't move from side to side on your dogs neck. If so, make sure the device is tight enough. Placing a rubber band on either side of the collar strap should prevent the device from moving from side to side.

IMPORTANT: Please read: In cases of no effective control (less than 15%) ABS recommends that an animal behaviourist be consulted.
The ABS Anti-Barking Collar is the most Humane, effective bark control system available. Properly used, it provides the necessary reinforcement for successful bark control. ABS Australia fully guarantees the Anti-Barking Collar from mechanical defects. It does not guarantee the individual's success.That depends largely on the individual's compliance with instructions and the stimulus of the dog's behaviour.

* Warranty Conditions:
This device is covered by a 12 month warranty from date of purchase for all resulting defects in materials and workmanship.

It does not guarantee to be effective on all dogs (approx. 88% success rate).
This warranty is limited to repairing or replacing parts that were found to be defective because of defects in materials and workmanship.

This warranty does not cover the accessories such as batteries, collars or aerosol.

This warranty will be deemed null and void should the purchaser attempt to effect his own repairs or modify the product.

This warranty does not cover problems caused by abnormal use or by not following instructions included in the kit.

In order for this warranty to take effect, the attached card must be returned within 15 days of purchase of the product with proof of purchase.
Specifically excluded from the warranty is damage due to shock, chewing, water-damage/submersion or exposure to high temperatures
(eg: being left in a car or near a heater).

This warranty is limited to the repair or replacement the option of the manufacturer.

This warranty cannot, in any way be used in cases of damage claims.
Once the warranty expires, the buyer is responsible for all costs relating to the purchase of replacement parts, labour and shipping.

Animal Behaviour Systems assumes no responsibility for any loss or claim by third parties that may arise through the use of this product.

Should you need to return your collar for servicing:
If you have a problem with your ABS Anti-Barking Collar check the following before contacting our office:

Is the battery flat? Is there citronella in the reservoir? Has the device been in water? Is the device switched on?

If your device has been in water, do the following:
Replace the old battery with a new one. A device that is water affected will exhaust the battery. Allow the unit to dry naturally or use a hair dryer.
If the unit still does not operate, contact our office for instructions on returning the ABS device for repair.

When returning your ABS Anti-Barking System for repair it is only necessary for the device and the battery to be sent. The collar, packaging and refill is not required. Please note: Sending in items not required may incur a postage charge. ABS Australia Pty. Ltd. will not be responsible for any goods arriving damaged from customers to ABS Australia Pty. Ltd.

Please allow approximately 48-72 hours for repairs from the date ABS receives the anti-barking device. ABS Australia Pty. Ltd. will not be held responsible for late delivery of items outside their control, eg postal & courier delays etc. All devices requiring repair that are outside the warranty will be subject to a Service Charge. Please note: the service charge does not include parts.

All repairs are returned to the customer via Australia Post. If a customer requires their collar back urgently or prefers using their own method,
it is suggested that they enclose an EXPRESS POST bag or their own courier
label etc. when returning the ABS device for servicing/repair.